Check out Intravia's Guide


Home  Service Guides Training Jim's Corner Order Form 

THE FOLLOWING ARE CORRECTIONS. SOME OF THESE HAVE ALREADY BEEN INCORPORATED INTO THE LATER PRINTINGS. WE HAVE NO WAY OF BEING ABSOLUTELY CERTAIN WHAT CHANGES ARE IN YOUR BOOK. PLEASE GO THROUGH THE LISTS AND YOUR BOOKS TO BE SURE YOU ARE UP TO DATE.

Corrections are posted on website.

Updated 11/26/03:

Corrections to 9th edition.

Table of contents: Kyocera-Mita 5055/6060. See page 66 (Konica 7060/7150.) 1/09/02. Done in rev 1.

Index: Page ix. Pencil in Lanier 5216, page 168 = Sharp AR-161. Lanier 5220, page 168 = Sharp AR-200. 7/02. Rev 2.

Page 1: Canon C130/NP7130/PC900 series. Stack feed bypass parts. Stack bypass pickup roller: FB1-7303. Stack bypass separator pad: FB2-5210. Stack bypass tray on machine: FB2-5175. Stack bypass tray flap: FB2-5177.

Page 5: Canon GP200/IR210. When replacing drum, shut power first. Cross out that stuff about function and execute. 3/19/03

Page 16: Canon C210. For service mode, change “user mode” key to “additional function” key twice in the first line. 9/02/

Page 20: Canon IR330/400. To reset web error code 005, you must first reset web counter in "Counter" mode. Go to COUNTER, then to "MISC," then to "FIX-WEB." 4/2/02. Rev 2.

Page 22: Canon IR330/400. To enter service mode, the “*” key you must press is in the “additional functions” section, not on the regular key pad. 12/19/02.

Page 40: Canon NP6050. To reset web error code 005, you must also go to service mode 4 to “error.”7/02 Rev 2.

Page 82: K-M 2310. Drum replacement. Sentence that says "Remove 2 screws…." Change that to "Remove 2 left side plates. Don’t lose screw retainers; they fall out. When handling unit, try not to turn over (to avoid toner in charge corona.") 10/12/01. Done in rev 1.

Page 94: Minolta Di181. Add this error code. COF30 ATDC sensor problem (toner sensor.) 8/02

Page 94: Minolta Di181. Simulation procedure. You must also press “STOP” after the “meter count” key to get into simulation. Pencil that in after meter count and before “Press 0.” 6/03

Page 101: Minolta Di250/350. To access “warm restart,” press switch through access hole with a straightened paper clip. The hole is near the LCD contrast on the right side of the operation panel.

Page 140: Ricoh Aficio 450 toner lockout: Go to SP mode 2-801 (ID sensor.) Shut power and when you turn back on it will be reset. Same procedure for hard drive error, but use hard drive simulation. 5/25/03

Page 181: Sharp AR-151/156/F152. Error code E7-01. Change to “Cancel with simulation 26-39. Set to “2.” 3/19/03.

Page 186: Sharp AR-162. 1st cassette and 2nd cassette pickup tires. The number is wrong. Those tires are not available separately.

Page 189: Sharp AR-162. Simulations 20 and 42 both require “sub code 1” to reset PM & developer lights. 6/03

Page 206: Toshiba 2570/3580. 0 & 5 mode; simulations 205-240 required the developer unit to be removed and the jig to be installed.

Page 226: Xerox® 212/214. Fuser reset procedure in simulation 401. After pressing “start,” you must also then press “stop,” and then shut power, wait 10 seconds and turn machine back on. 6/03

Corrections to 8th edition.
Note: Look and see if your first inside page says “Revision 2.” If so, then all items for the 8th edition listed as “Rev 2” are done in your book.


Page ix of index. Pencil in Lanier 5216 & 5220 same as Sharp AR-160 & AR-200. 11/12/00 Page xvii of index. Toshiba 2050 is on page 142, not page 124.

Page 1. Canon C250/C330/NP6330. Pencil in "ADF little motor: FF2-5903." 7/02 Rev 2.

Page 6. Canon C250/C330/NP6330. Last section. Counters mode. Substitute "additional functions" for "user mode." Rev 2.

Page 30. Konica 2223. Trouble code F09. Must be cleared with 25 mode, code 49. Set to "0." 4/11/01. Rev 2.

Page 53. Konica 7050. Cross out the paragraph that says to go to 36 mode for CVR adjustment for copy quality. Copy quality adjustments are in 47 mode. 02 for charge corona (Press "P" Use number keys to change value and press "P" key to lock in. 07 for charge corona grid voltage (Press "start print." Use number keys to change value and press "P" key to lock in. 11 for bias voltage (Press "P Use number keys to change value and press "P" key to lock in. (12/14/00) Rev 2.

Page 61. Konica 7410 part number of fuser gear & idler gear. One of them is 25VE77010, the other is 25VE77100. We have received conflicting info. I suppose you need to order both to be safe. 01/27/02 Rev 2.

Page 68. Minolta 1030-1031F. In tech rep choice, for c5 & c6, you must be in "Auto Exposure." 10/1/01 Rev 2.

Page 72: Minolta 1070. 1st line. Change Hold down panel reset key for 3 seconds to Hold down panel reset key for 6 seconds. Rev 2.

Page 102: Mita 1515. To enter simulation, front door must be open. 3/20/01. Rev 2.

Page 105. Mita 1860/2360. Part numbers of developer gears; 19t & 17t should read 34914200 & 34914210. Mistakenly printed as 348-----. 8/10/00

Page 134. Ricoh Aficio 200/250. Simulation procedure. Press "Clear modes" key, not "clear/stop." I am told it may require pressing 2-3 times. 8/9/00 Rev 2.

Page 151: Ricoh 4622/4822. Paper feed section 1 is the bypass, not the cassette. For cassette paper feed, you should use four each of the part number listed for paper feed pickup rollers for each cassette. Order eight rollers to rebuild both paper feeds. 5/25/03

Page 163. Sharp AL-1000 etc. Fuser thermal switch correct part number has last digit changed to "2." Should be CTHM-0019FC52. 7/02 Rev 2.

Page 168. Sharp AR 160. Equivalent machines. Pencil in "Lanier 5216 & 5220." 11/12/00

Page 169. Sharp AR 160. Fuser roller drive gear part number should read NGERHO540FCZ1 (0 not Q). 6/1/01. Rev 2.

Page 169. Sharp AR 160. Add this part number. Developer seal blade PSEL-0001YSZ1 (AE) 7/02 Rev 2.

Page 170. Sharp AR 160. Correct heat lamp part number is RLMPU0006QSZZ (change the 7 to a 6.) 1/17/02.

Page 172. Sharp AL 1600-1670. To enter simulation. Different keys than AR machines. Press "Clear, Exposure, Clear, Exposure." All should be the same after that. You must use 22-5 to read total count. Some simulations require "Print" to be pressed twice. 8/11/00 & 11/12/00. Rev 2.

Page 173. Sharp AR160-200, AL1600-1670. Simulation 20; add sub code 1 to clear PM counter. Rev 2.

Page 174. Sharp AR160-200. Simulation 64 applies to all. Cross out "200." 7/15/00 Rev 2.

Page 210. Xerox XC23 etc. Copy quality adjustment. Add "VR1 on main board on rear of machine." 4/30/01. Rev 2.

Page 220. Xerox 5624, 5824, 5828, 5830. Note: To clear fuser errors, you must, at some point "P" scroll to "Routines." 7/02 Rev 2.



Corrections to 7th edition:

Table of contents & Index. List Mita 2355 with Mita 1856

Index. Add Canon 6012/F in 6th edition page 5. Note that top of pages 5, 6,7 you should change 6212 to 6412. Actually I should, but I don’t know where your book is.

Index. Add Gestetner 2713 in 7th edition, page 132. Cross reference is Ricoh 3513.

Index. Add Panasonic 7718 in 7th edition, page 114.

Page 58. Minolta 1083/2010: Developer is added through toner port, which was only a guess previously.(6/99)

Page 109: Panasonic 7713/7715. To enter service mode, press these three keys, in sequence, continuing to hold each as you press the others. Paper tray, zoom down, 1. To exit service mode, press these three keys, in sequence, continuing to hold each as you press the others, Paper tray, zoom down, clear/stop. 5/25/03

Page 115, 116 & 121. Panasonic 7718-7735. Add trouble code U14 on page 115: Toner waste bottle full. For User preset mode access code, use 0,0,0. On page 121, F8-08 should be F8-09. 4/15/01

Page 116. Panasonic 7718-7735. Also, probably do the same for the Panasonic 7742/50. To enter service mode, press these three keys, in sequence, continuing to hold each as you press the others. "User preset" "Original size 11x17" "3". To exit service mode, you may have to use the sequence listed, rather than pressing simultaneously, as listed in the book. (4/2000). I have also been told that to exit the "F" modes, you need to hold down the "user preset" & "stop/clear" keys at the same time.

Page 120. Panasonic 7718-7735. Resetting PM will also require resetting Fuser Web Count (F7-26). Apparently, do F7-26, and exit simulation. Than do F7-26 again and enter 80,000 to shut service wrench symbol. 11/12/00

Page 135. Ricoh 3513/3713. Outputs. After pressing "9", press "Auto ID." Further down the page. After output 10, the next two (toner motor and registration clutch) should be numbered 11 & 12. Likewise, Exposure lamp and Total counter are numbers 20 & 21.

Page 137. When doing developer calibration, cover the glass with clean white paper first. (6/99)

Page 143 Ricoh 4015,. Simulation 93. The ??? are to be replaced by "Exposure darken key" and by "Auto Image Key." (5/99)

Page 145: Ricoh 4022/4522. Developer calibration. Lots of changes. Very important. Press "Clear/stop." Press "1". Press "0" Press "7". Press and hold "Clear/stop" for 3 seconds. Press "Clear/stop" again, briefly. "Press "2" Press "Enter" Press "2" Press "1" Press "4" Press "Enter" Press "Start". Machine will now run and set up developer. (5/1/2000). Note: previous version of this correction listed this procedure for 4015; that was a mistake. This is for 4022. 4015 was ok.

Page 170. Sharp 2216 has different PM cycle settings in simulation 21. 0 is 60,000 copies. 1 is 30K, 2 is 10K, 3 is 5K, 4 is 2500 copies (2.5K.) 5 is no PM indicator. 3/8/02

Page 175: Sharp 2025/2030/2040: Exposure adjustment. Add this. Press “scroll display” button (next to digit display) to move cursor to AE1. Set AE1 to {0.” Set AE5 between 560 and 620 for best copy quality. Press “CA” to exit. 5/03.

Page 176. Sharp 2030, 2040 & maybe others. H5 code is a fuser problem not listed in factory manual either. To reset, turn power on and open front door. Press and hold exposure key while closing front door. 10/2/00

Page 187: Sharp 2314. Simulation 30 should be added in front of Sub code 1 in middle of page to test sensors and switches. (9/00)

Page 187. Simulation 42. C00C 42, Print, then press "0" "0" then print. Completely cross out the two sub codes listed below that. They were mistakenly pasted in during final editing and do not apply to that machine at all. (2/2000).

Page 190. Sharp Z810. In copy quality adjustment, cross out the last sentence that begins "To make the easiest……"

Page 191. Sharp Z810. User simulations do not apply to Xerox®.

Page 192. Sharp Z810. Simulation 22-12 checks drum count. Not 23-12. 9/02.



Corrections to 6th edition.

Page 5: Canon PC710-770 and 6012 Reset procedure pins. For PC copiers the pins are JP1 & JP2. For 6012 and C120, the pins are JP3 & JP4. Also, the main board (DC controller) is in the top front of the machine, not the rear.

Page 9: Canon C160 and NP6016. First line of copy quality adjustment. "Knob inside front on left." For PC850 there is a slide control.

Page 9: Add this somewhere that you can see it. To read total counter on PC850, enter service mode. Press "6". Press "AE." Press "6" "0" "3". Press "Start." You will get a 3 digit display. Multiply by 100 for a reading. 657 = 65,700 copies (between 65,700 & 65799 actually).

Page 15: Canon 6025/6030. "*" key might be under the special features panel.

Page 22: Canon NP6060. Very last line. Waste toner. Cross out "rear of machine."

Page 23. Konica 1015. F26 Toner adjustment problem mode. Go to 47 mode; 51.

Page 24. Konica 1015. P26. Must adjust TDS in 47 mode, 51.

Page 26. Konica 1015. In 47 mode, output 51 is developer calibration. "51" will flash as machine cycles for about 3 minutes. When it stops flashing, calibration is complete.

Page 27. Konica 1015.
Trouble code 26: Toner sensor problem. This means the machine is undertoned. To repair, replace the developer and enter "47" mode. Press 51. Press Print. Allow the machine to cycle until it stops. Some feel that you should disconnect the toner motor first. This code happens, probably because either the machine wasn’t set up properly, or because the customer kept using the machine when the toner light was on.
Developer calibration: After changing developer, enter "47" mode, output 51. Press "Print." Display will flash 51 and machine will cycle for about 3 minutes. If this is not done at 40K developer cycle, machine will often (maybe always) go into a code 26 and will not operate.

Outputs in 47 mode that were omitted in first printing. If you are missing them, call and we will fax you the corrected page.  Page 32: Not a correction, just a clarification since it was not pointed out.

Konica 3135, 4145, 4155, 4255 have no developer calibration required.

Page 38: Minolta 1080/1081: Squeeze this in somewhere. Reset switch on PWB-A. Can also jumper PJ22 or jumper Memory to GND, or Total to GND.

Page 56. Mita 1256/1257. Where it says Ub, change the word "can" to "might". Meaning you might be able to reset, by replacing fuse or turning drum through a revolution. Add the following trouble codes. OF: Replace drum and developer units (entire process unit} on 1256. U1: total counter.

C72 could also be blank lamp. PF is paper feed. AP means adding toner while machine is idling.

Page 57. There might be a simulation 59 for trail edge void.

Page 79. Panasonic 7113. To enter service mode, press "paper tray" "Zoom down" and "1"
simultaneously. To exit service mode, you may have to press these 4 keys, not just the 3 in the book. "Paper tray" "Zoom down" "1" "Clear/stop." That procedure may be wrong. The following may be the correct one. To enter service mode, press these three keys, in sequence, continuing to hold each as you press the others. Paper tray, zoom down, 1. To exit service mode, press these three keys, in sequence, continuing to hold each as you press the others. Paper tray, zoom down, clear/stop. 5/26/03

Page 83. Ricoh 3013/3213: Developer calibration.
Enter SP mode . Close platen cover. Press "7". Press and hold "Clear/stop" until "." displays in the top left. Press "Clear/stop". "5" will display. Press "6". Press "5". This might be done with the quantity decrease (-) key. Press "Auto image density Key". "50" will display. Press "Start".

Page 95: Ricoh 4215/4220/4222: Developer replacement. In the explanation, add. Turn dipswitch 101-4 on. "5" will flash in display. Press "6". Press "5." Press Print. Machine will run for several minutes and when done will return to normal mode. Note that this is the 2nd correction to this particular machine’s developer calibration and supercedes the previous one. (4/99)

Page 117: Sharp 2014 group of machines. To reset drum counter. Use simulation 24-007

Page 119: Sharp 2014 simulations. To enter a sub code, key in the number of the sub-code, and then press "Print."

Page 120: Sharp 2214 document feeder registration adjustment: Simulation 50; sub code 01: Press paper select button until both cassette indicators light. 10/18/01

Page 130: Sharp 2116/2118. Near top of page. Change "Sub code 30." To Simulation 30, sub code 1. (9/00)

Page 141: Toshiba 1340/1350. 0 & 8 mode. After "Enter the new value", it should read "using the 1 and 7 keys." Also, note that you can make a test copy by pressing 3 & 4 keys simultaneously.

Page 145: Toshiba 1650/2050 C7 reset. 87 should read 89.

Page 148: Toshiba 1340/1350: C7 fuser problem is reset with 0 & 8 mode, code 89. Replace 0&5 with 0&8. 1/12/01.

Page 153: Toshiba 3550/4550/6550. Very important. Developer calibration. Cross out the part of the sentences that says "….full cycle. When it finishes…." We have found that this can cause major problems. The cycle should be watched, adjusted and terminated, within 2-3 minutes.

Page 159: Toshiba 3550/4550/6550: 80 phone number. Add the following. "Press clear to erase. Press "Interrupt". Press "Print" to lock in new number.

Page 160: Xerox 5312/13/14: Copy quality adjustment. After pressing "start" machine will start to make copies. While it is making these 10 copies, change the value with the "0" or "5" keys. 5/00.

Cross reference: Wherever you can fit this. Probably stick inside back cover and make a note at the beginning of the Xerox 5340 section. 10/15/01. 6th edition: Xerox 5337, 5340, 5343, 5450, 5352 fuser web reset. Note that some earlier 5340s and 5350s did not require a procedure other than replacing the web. However, on most models of this group, code 10-320 will display at 250,000 copies. Procedure: Hold "Job Interrupt" button & 5 key while turning on power. Enter 4 digit access code (default code is 8765.) this will not show in the display. If this code does not work, and you cant get the correct code, do the following. Get total copy count by pressing "Review" button on console and then pressing "Billing meter" on touchscreen. Use the last 4 digits of the total count backwards, as the access code. Note that reading the screen will be rather difficult due to the trouble code flashing at you. Once you see the status code screen, press "stop" twice to display the diagnostic screen. Press the HFSI button. Press "Ovr. Thresh" to bring up HFSIs (high frequency service items) which are over the threshold. Using arrows, scroll down to web count. Press "Reset Item." Press "Print" to lock in. Next, select the "DC Routine" screen. Enter "131." Press "Print" to lock in. Press "M/C/Set" button. Press "Print" to confirm reset. To exit diagnostics, press "Service info. Touch "Cal Close." Choose "Quick Exit." Thanks to Britt at Parts Drop (201)387-7776

Page 178. Add Lanier 6112, cross references to Toshiba 1210, which is similar.

Page 180. Cross out Panasonic 1780 reference to 5th edition. It is correctly listed with the 1680 for the 6th edition.



CORRECTIONS TO 5TH EDITION

Page 4. Canon 3050. Counter mode reset. Cheat interlock. Actuate service switch. You will see a "$" sign in the display. Press *. Press 6. Press *. Scroll through display (using exposure keys) until you get the counter you want (such as "Web"). Press "Clear/stop" and service switch simultaneously. Remove cheater. January 1998.

Page 7: Canon 3325. Add the following to the bottom of the page. "To clear counter, such as web reset. Actuate service switch (with door interlock cheated). Press (*) Press (6) Press (*). Next, press the following keys simultaneously. *, 0, Clear/stop. March 1997. Revision 3.

Page 15: Konica 1018/2020/2028/3035 do not require any developer calibration or setup. However, the 4045 does and here is the procedure: Place 11x17 clean white paper on glass. Insert empty 11x17 cassette. Go to "36" mode. Enter "01." Select 11x17 paper (empty cassette.) Take out of ADF mode. Select 30 copies. Press "Start." After 30 copies (presumably 30 cycles) have finished, shut power and restore machine to normal. 9/13/01

Page 26: Minolta 2120-2151. "Toning up Procedure." Should read. "Hold down the Clear/stop key while turning on power. Toner/developer ratio can be changed in the choice mode." Changed July 94.

Page 28: Minolta 2120-2151. Under heading for "Display mode," delete "2150/2151." These apply to all models in this group, not just the 2150/2151. Changed July 94.

Page 42: Minolta 5320. Oil can indicates PM and fuser web reset. Must do both. 3/15/02. Waste toner light reset: Press tech switch inside front door on jam reset board. Press “4.” The first number to display is the PM count. Push the switch again for the waste toner count. Press “C” on control panel to clear. Then enter 120,000. 5/26/03

Page 47: Mita 1415/1435/1455 developer calibration. After "Add the rest to the empty developer unit," this is what I have added, though this is kind of lengthy and I am sure you will make up your own version of it. "We keep hearing questions and opinions on ho to correctly calibrate developer on these. Developer is a different quantity than 1205/1255, but is the same material, as is the toner. The following procedure appears to work. Remove one rounded capful (Rounded, not heaping. This is not Nestles Quick.) of developer from the bottle. Add the rest to the developer unit and follow the rest of the procedure.

Page 47: Mita 1415/1435/11455: Replace copy quality adjustment with "Copy quality adjustment and registration adjustment apply only to the 1415. For the 1435 and 1455, see the simulation section.

1415 Copy Quality: Turn on dip switch 1-1 on main board. Adjust VR2 on main board for image at the center LED. Adjust VR3 for image on exposure setting (lighter copy). Note: Main board is located under the left "outrigger."

1435/1455 Copy Quality: Use simulation 24. Use zoom keys to change settings.

1415 Registration: VR4 on main board.

1435/1455 Registration: Simulation 58. December 1994. Revision 2.

Page 48: Mita 1435 exposure adjustment. Sim 24. Press Print. Press "All clear/reset." Adjust as needed. press "stop/clear" to lock in. This may be unclear in 5th edition. 03/15/02.

Page 49: Mita 1415/1435/1455: Dipswitch adjustments here are for 1415 only. December 1994.

Page 51: Mita 1855, 2155, 2156.

Under heading "Simulations" the procedure to enter simulation mode should read "Press 1087, 1087, Reset." Enter the number of the code you wish to use. Press "Print." July 1994. Revision 1.

Page 79: Panasonic 5060. By heading "PM Count Reset" procedure is "F5 Mode. "01", "Reset" If PM indicator is still lit, you may have to reset the fuser cleaning web. Use F5 mode. Press 9, 9, "Memory in" "Reset". Also, check or replace the fuser cleaning web at that time. To exit, press "Edging" "2 Page Copy" and "Reset" simultaneously (at the same time.) Note that the PM indicator is the picture of the technician. July 1994. Revision 1.

Page 85: Regarding Ricoh 3113/3313. I believe that to enter simulation, you do NOT press interrupt. If any problems here, use the procedure described above for the 6th edition, page 83, or follow the procedure in your 7th edition for the 3513 (page 133). 4/2000

Page 86: Ricoh 3113, 3313, 4415, 4418, 4421, 4427, 4727, 5433, 5733. Under heading "ERROR CODES," it should read the following: "Error codes will be accompanied by a symbol of a wrench in the display." July 1994. Revision Page 86: Ricoh 4427/4727 & maybe others. To clear waste toner code "E70." Hold "1" & "3" while turning on power. Press "8," Press "3". Press "Enter." Press "1." Press "Enter." Turn power off and then back on again. 11/05/01.

Page 99: Minolta 5420 waste toner reset procedure. Insert this stuff somewhere. Plenty of room on that page.

10/12/01. To clear waste toner. Cheat door switch. Press switch 121-1. Press "4." Press switch 121-1. Press "Clear." Enter new countdown number (such as 25,000.) Press "Panel reset."

Page 117  " Toshiba PM Reset Procedure. Change to read: PM read/reset. Hold 0 and 8 while turning on power. Enter 79. You will read the copies since the last PM. To reset, press "Print." Enter 00, Interrupt, 00, Interrupt, 00, Interrupt. Press 0 and 9 simultaneously to exit. March 1997. Revision 3.

Page 117. Toshiba 1710, etc. Copy quality adjustment. Should read the following. "Go to 0 and 5 mode." 8 was wrong. April 1997. Revision 3A.

Toshiba 1710 and probably all Toshibas. Under "C7" code the proper reset procedure is: "Hold 0 and 8 while turning on power. Enter 89. Display will show 3 (indicating fuser fault). Press 0, 0, interrupt. Turn power off for a few seconds and then back on. July 1994. Revision 1Page 122 Toshiba simulations. At simulation 89, it should read: "Hold 0 and 8 while turning power. Enter 89. Display will show "3." Press 0, 0, interrupt. Turn power off for a few seconds and turn back on. July 1994. Revision

Page 123. Toshiba 9230. Change the PM reset procedure to read the following. "PM read and reset: Hold 0 and 5 while turning machine on. Use code 79 to read current PM count and to reset PM count back to 0.


Please be aware. We update these revision sheets as soon as possible, and try to update future printings of each edition. Like manufacturer's manuals, we are not perfect. Bear in mind that we get corrections and revisions only from people like you. We receive no bulletins, help, information or assistance of any kind from manufacturers.
Jim Intravia


Home  Service Guides    Training  Jim's Corner  Order Form